Komatsu PC200-7, PC200LC-7, PC210-7 & PC210LC-7 Repair Manual PDF

Serial Number:
PC200-7: DBB0001 and up
PC200LC-7: DBE0001 and up
PC210-7: DBF0001 and up
PC210LC-7: DBG0001 and up
PC220-7: DBH0001 and up
PC220LC-7: DBJ0001 and up
Manuals: Shop Manual
01 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01-1
10 STRUCTURE AND FUNCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
20 TESTING, ADJUSTING AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-1
30 DISASSEMBLY AND ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-1
90 OTHER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90-1
1. Composition of shop manual
ease of understanding, the manual is divided into the following sections.
00. FOREWORD
This section explains the safety and basic information.
01. GENERAL
This section explains the specifications of the machine for the Excavator.
10. STRUCTURE AND FUNCTION, MAINTENANCE STANDARD
This section explains the structure, function, and maintenance standard values of each component.

The structure and function sub-section explains the structure and function of each component. It serves not only to give an understanding of the structure, but also serves as reference material for troubleshooting. The maintenance standard sub-section explains the criteria and remedies for disassembly and service.

20. TESTING AND ADJUSTING
Standard value table

This section explains the standard values for new machine and judgement criteria for testing, adjusting, and troubleshooting. This standard value table is used to check the standard values in testing and adjusting and to judge parts in troubleshooting.

Testing and adjusting

This section explains measuring instruments and measuring methods for testing and adjusting, and method of adjusting each part. The standard values and judgement criteria for testing and adjusting are explained in Testing and adjusting.

Troubleshooting

This section explains how to find out failed parts and how to repair them. The troubleshooting is divided by failure modes. The S mode of the troubleshooting related to the engine may be also explained in the Chassis volume and Engine volume. In this case, see the Chassis volume.

30. DISASSEMBLY AND ASSEMBLY Excavator

This section explains the special tools and procedures for removing, installing, disassembling, and assembling each component, as well as precautions for them. In addition, tightening torque and quantity and weight of coating material, oil, grease, and coolant necessary for the work are also explain.

90. OTHERS (chassis volume)/Repair and replacement of parts (engine volume)
Chassis volume
This section gives hydraulic circuit diagrams and electrical circuit diagrams.
Engine volume
This section explains the method of reproducing, repairing, and replacing parts.
Measurement of oil leakage amount from bucket cylinder
1) Start the engine and keep it running until the hydraulic oil temperature rises to the operating range. Then extend the bucket cylinder to the digging stroke end.
k Release the pressure remaining in the piping, referring to the foregoing section of “Release of Remaining Pressure in Hydraulic Circuit”.
2) Disconnect hose (3) at the cylinder head end block the hose end with a plate.
k Be careful not to disconnect the hose at the cylinder bottom end.
3) Start the engine and apply the relief pressure to the bottom end of the cylinder with the engine running at high idling.
4) Continue this condition for 30 seconds, then measure the oil leakage amount for one minute.