Fendt 818, 820 Vario COM III Tractors Workshop Repair Manual

Manual for: AGCO Fendt

Series: 800 Vario COM III

Format: PDF

English

Fendt 818, 820 Vario COM III Tractors Workshop Repair Manual – 1244 Pages

Fendt 800 Vario COM III Wiring Diagram and Schematics – 76 Pages

Testing instructions Auto-Guide System Manual – 316 Pages

Greentec Two Tank System Manual – 330 Pages

Technical Data – 62 Pages

Operators Manual – 341 Pages

Repair Schedules – 176 Pages

Please see below details on applicable models

Fendt 818, 820 Vario COM III Tractors Workshop Repair Manual

Manual for: AGCO Fendt

Series: 800 Vario COM III

Format: PDF

English

Applicable Models:

Model	Chassis Number	Serial
FENDT 818 Vario COM III	729	1001-
FENDT 820 Vario COM III	731	1001-

Fendt 818, 820 Vario COM III Tractors Workshop Repair Manual – 1244 Pages

Fendt 800 Vario COM III Wiring Diagram and Schematics – 76 Pages

Testing instructions Auto-Guide System Manual – 316 Pages

Greentec Two Tank System Manual – 330 Pages

Technical Data – 62 Pages

Operators Manual – 341 Pages

Repair Schedules – 176 Pages

Workshop Manual TABLE OF CONTENTS

0000 Overall system/tractor

A General 5

B Faults 31

D Component position 107

F Settings and calibration 221

1000 Transmission

1005 Transmission control system 5

1010 Differential unit 29

1015 Final drive axle 67

1030 Hand brake 73

1070 Brake system 79

1080 Vario unit 109

1100 Clutch operation 125

1150 Cardan brake 129

1200 Front PTO 143

1220 Live PTO 171

1320 Front wheel drive 195

1430 Hydrodamp 207

2000 Engine

2000 Engine 5

2010 Cylinder head 45

2060 Fuel system 51

2312 Lubrication 77

2400 Exhaust gas system 85

2712 Injector 91

3000 Front axle

3020 Axle body 5

3050 Suspension 9

3180 Cardan shaft 21

5000 Vehicle layout

5200 Cab bearing, suspension 5

5500 Air conditioning system

5500 Air conditioning system 5

5570 Electrical wiring 11

8100 Cab

8100 Cab 5

8600 Power lift

8610 Electrohydraulic EPC control 5

8618 External control 43

8631 Power lift control 51

8800 Compressed air system

8800 Compressed air system 5

8810 Air compressor 33

8830 Brake fittings 37

8890 Air reservoir 55

8900 Front loader

8900 Front loader 5

8970 Piping 27

9000 Electrical system

9000 Measure and test 5

9400 Hydraulic pump installation

9420 Transmission pump 5

9600 Hydraulic equipment

9600 Hydraulic equipment 5

9700 Electronics

9700 Electronics 5

9717 LBS – agricultural BUS system 27

9740 E-box 39

9770 Control panel 47

9900 Service

9920 Special tools 5

Manual Extract

This workshop manual provides notes for trained technicians to maintain our tractors. Read and observe the information in this documentation. This will help you prevent accidents.

Intended use includes maintaining operating the service and maintenance conditions as specified by the manufacturer. Operation, maintenance and repair of the tractor may only be carried out by people who are familiar with this equipment and aware of the associated dangers. Ensure that this documentation is available to and understood by everyone involved in operation, maintenance and repair. Not observing this documentation

can lead to faults, damage and personal injury.

The prerequisite for the Fendt 818, 820 Vario COM III tractor being correctly serviced and maintained is the perfect condition and availability of all necessary equipment, standard tools and general workshop equipment as well as special tools. Special tools must only be used where absolutely necessary. The tools are displayed where they need to be used in each case.

The machine must be maintained according to its proper use. Always replace parts with genuine FENDT spare parts! When ordering parts, please provide the chassis number as per the most up-to-date spare parts documentation.

Workshops should also refer to documentation on maintenance work and technical data. Once maintenance is complete, take a test drive to ensure the vehicle’s correct operation and road safety.