Fendt 711, 712, 714, 716 Vario COM II Tractors Workshop Repair Manual

Manual for: AGCO Fendt
Series: 700 Vario COM II
English
Fendt 711, 712, 714, 716 Vario COM II Tractors Workshop Repair Manual – 1246 Pages
Fendt 700 Vario COM II Wiring Diagram and Schematics – 61 Pages
DEUTZ BF Engine Manual – 498 Pages
Operators Manual – 267 Pages
Technical Data – 33 Pages
Please see description below for applicable models
Applicable Models:
| Model
| Chassis Number
| Serial
| FENDT 711 Vario COM II
| 711
| 8001-
| FENDT 712 Vario COM II
| 712
| 8001-
| FENDT 714 Vario COM II
| 714
| 8001-
| FENDT 716 Vario COM II
| 716
| 8001-

Workshop Manual TABLE OF CONTENTS

0000 Tractor / General system
1000 Transmission
Transmission control unit
Differential
Axle drive
Handbrake
Housing
Brake system
Vario transmission unit
Emergency control
Clutch actuation system
Cardan brake
ML range control
Front PTO
Live PTO
Front-wheel drive
Hydrodamp
Hydraulic pump
Transmission lubrication system
Pump drive
ML adjustment
Enhanced control system valves
Enhanced control system pipes
2000 Engine
Engine
Cylinder head
Fuel system
Exhaust gas system
3000 Front axle
Front axle support
Axle housing
Suspension
Suspension valve fitting
Suspension pipe
Track rod
Steering cylinder
Frame
Cardan shaft
Diff. lock actuation system
4000 Steering
Steering wheel
Hydraulic steering assembly
5000 Vehicle Body
Design
Driver seat
Trailer hitch
Trailer hitch coupling
Cab mount, suspension
5500 Air Conditioning System
Compressor drive
Coolant lines
Evaporator
Condenser
Electrical cables
8100 Cab
Heater
Ventilation
Windscreen wipers
Cable loom
8600 Power lift
Electrohydraulic EPC control
External control
Control lifting gear
8700 Three-point hitch
Lift arms
Support
8800 Compressed air system
Compressor
Brake fittings
Lines
Electrical actuation system
Air tank
8900 Front loader
Mounting frame
Hydraulic implement actuation system
3. hydraulic circuit
Multi-coupling
Pipes
Lift cylinder
9000 Electrical System
Alternator
Starter lockout
Fuses
Battery system
Starter motor system
9200 Front power lift
Lift gear
External control
Cylinder
Pipes
Enhanced control power lift
Frame
9400 Hydraulic pump assembly
LS pump
Transmission pump
Steering pump
9500 Hydraulic pipes
Base circle
Power lift
with oil cooler
Hydraulic trailer brake
Steering
Reversing system
9600 Hydraulic equipment
Hydraulic connections
Central control block (ZSB)
Valve assembly
External pressure supply
Valve supplement
9700 Electronics
Instrument panel
Terminal
LBS – agricultural bus system
Transducer
Radar sensor
E-box
Transmission actuator unit
Drive switch
Control panel
Engine EDC
ECU, lift gear
9900 Service
Special tools
FENDIAS
Manual Extract

Intended use includes maintaining operating the service and maintenance conditions as specified by the manufacturer. Operation, maintenance and repair of the tractor may only be carried out by people who are familiar with this equipment and aware of the associated dangers. Ensure that this documentation is available to and understood by everyone involved in operation, maintenance and repair. Not observing this documentation

can lead to faults, damage and personal injury.

The prerequisite for the Fendt 711, 712, 714, 716 Vario COM II tractors being correctly serviced and maintained is the perfect condition and availability of all necessary equipment, standard tools and general workshop equipment as well as special tools. Special tools must only be used where absolutely necessary. The tools are displayed where they need to be used in each case.

The machine must be maintained according to its proper use. Always replace parts with genuine FENDT spare parts! When ordering parts, please provide the chassis number as per the most up-to-date spare parts documentation.

Workshops should also refer to documentation on maintenance work and technical data. Once maintenance is complete, take a test drive to ensure the vehicle’s correct operation and road safety.