Doosan DX210W Wheeled Excavator Shop Repair Manual PDF

Table of Contents:-

Safety
Wheel Excavator Safety …………………………………………………………….. SP000956
Specifications
Specification for DX210W…………………………………………………………… SP000957
General Maintenance
General Maintenance Procedures……………………………………………….. SP000016
Standard Torques……………………………………………………………………… SP000813
Upper Structure
Cabin ………………………………………………………………………………………. SP001231
Counterweight…………………………………………………………………………… SP000959
Fuel Tank…………………………………………………………………………………. SP000961
Fuel Transfer Pump…………………………………………………………………… SP000021
Swing Bearing…………………………………………………………………………… SP001232
Swing Reduction Gear……………………………………………………………….. SP001233
Lower Structure and Chassis
Ram Lock Valve………………………………………………………………………… SP000923
Selector Valve…………………………………………………………………………… SP000926
Double Pilot Check Valve …………………………………………………………… SP000927
Solenoid Valve………………………………………………………………………….. SP000928
Front Axle ………………………………………………………………………………… SP000929
Rear Axle…………………………………………………………………………………. SP000930
Engine and Drive Train
Transmission ……………………………………………………………………………. SP000962
Drive Coupling (Main Pump)……………………………………………………….. SP000963
Hydraulics
Hydraulic System Troubleshooting, Testing and Adjustment …………… SP001097
Accumulator……………………………………………………………………………… SP000984
Center Joint (Swivel)………………………………………………………………….. SP000919
Cylinders………………………………………………………………………………….. SP001098
Main Control Valve ……………………………………………………………………. SP000966
Swing Motor……………………………………………………………………………… SP000985
Travel Motor……………………………………………………………………………… SP001110
Counterbalance Valve ……………………………………………………………….. SP000991
Main Pump & PTO…………………………………………………………………….. SP000988
Gear Pump ………………………………………………………………………………. SP000989
Service Brake Supply Valve ……………………………………………………….. SP000990
Dozer Control Valve…………………………………………………………………… SP000992
Steering Valve ………………………………………………………………………….. SP000993
Accelerator Pedal Valve (Hydraulic) …………………………………………….. SP000964
One Spool Valve……………………………………………………………………….. SP000996
Remote Control Valve (Work Lever / Joystick) ………………………………. SP000069
Breaker EPPR Valve (Opt) …………………………………………………………. SP000192
Service Brake Pedal Valve …………………………………………………………. SP001006
Solenoid Valve Assembly …………………………………………………………… SP000997
Hydraulic Schematic………………………………………………………………….. SP001107
Electrical System
Electrical System ………………………………………………………………………. SP001108
Electrical Schematic ………………………………………………………………….. SP001256
Attachments
Boom and Arm………………………………………………………………………….. SP001255
Bucket……………………………………………………………………………………… SP001001
Doosan DX210W Manual Instruction Extract:
Inspection

The center joint should be checked for evidence of external oil leakage every 2,000 operating hours. Leaking or defective Orings are an indication that dirt and other contaminants could be getting inside the assembly, which will promote accelerated, abnormal wear and may cause early failure of the assembly.

If internal seals or other sliding surface components are worn and there is internal fluid leakage, complete overhaul and repair or replacement of the center joint may be required.
Testing
To check pressure through the center joint, make up a test kit from the following equipment list:
700 bar (10,000 psi) pressure gauge.
Adapters, connectors, piping and flange block-off plates conforming to those used in high-pressure piping connections of the excavator.
A high-pressure relief valve with a setting pressure 1.5 times maximum system pressure.
A stop valve.
A manually operated, in-line changeover valve.

Install the changeover valve upstream from one of the stem high-pressure ports. Connect the pressure gauge downstream from one of the body ports. Install the stop valve between the changeover valve and the stem of the center joint. Other components should be installed according to the layout in the block diagram. The test kit is used to pressurize the center swivel above normal working pressure and lock in the higher pressure (as the stop valve is closed manually) for a leak down test.

NOTE: The same type of kit can also be made up for the drain port (return line) side of the center joint. Use appropriate piping, connectors, test gauges, etc., and follow the same block diagram general layout (Figure 2).

How to Use The Doosan DX210W Excavator Guide Manual:

This manual provides information for servicing the DX210W Doosan Excavator. All service procedures are broken down into detailed steps, listed in their recommended sequence. The manual uses both photographs and drawings to help locate and itemize components. The table of Contents on the preceding pages is your best tool for finding the service procedure you need. Be certain to observe all Safety information included in these pages.

A schematic of each of the major engine systems is provided at the beginning of the section of the manual devoted to troubleshooting and repairing that particular system.

Basic safety precautions are list in the Safety section of the Doosan DX210W Excavator Service Manual. Additional safety precautions are list in the Safety section of the owner/operation/maintenance publication. Specific safety warnings for all these publications are provided in the description of operations where hazards exist. WARNING labels have also been put on the product to provide instructions and to identify specific hazards.