Case Farmall 70, 80, 90, 95 Tractor Repair Manual

Manuals: Service Manual

SECTION 00 – GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SECTION 10 – ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SECTION 18 – CLUTCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

SECTION 21 – TRANSMISSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SECTION 23 – DRIVE LINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

SECTION 25 – FRONT AXLE MECHANICAL TRANSMISSION . . . . . . . . . . . 9

SECTION 27 – REAR AXLE AND TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . 11

SECTION 31 – POWER TAKE-OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

SECTION 33- BRAKING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

SECTION 35 – HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

SECTION 41 – STEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

SECTION 44 – FRONT AXLE AND WHEELS (2WD) . . . . . . . . . . . . . . . . . . . . . 18

SECTION 50-CAB AIR CONDITIONING SYSTEM . . . . . . . . . . . . . . . . . . . . . . 19

SECTION 55 – ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

SECTION 90 – PLATFORM, CAB, BODYWORK . . . . . . . . . . . . . . . . . . . . . . . . 25

The following pages are the collation of the contents pages from each section and chapter of the Farmall 70, Farmall 80, Farmall 90, Farmall 95 Service manual. Complete Service part # 84253591.

Manual Extract: Refit the injection pump
Installation
To refit the injection pump, proceed as follows:
1. Respect the tightening torques prescribed on page 12.
2. When refitting the BOSCH injection pump, insert the stud bolts in the engine flywheel casing into the mating holes on the pump flanging.
3. Do the timing for the injection pump in relation to the drive gear, proceeding as described on page 100.
4. Then loosen the retaining and safety bolt of the injection pump timing.
5. Reinsert the L spacer and tighten the retaining bolts.
6. Free the engine flywheel, take out the tools 380000988 and 380000732 and refit the starter motor.
7. Reconnect the pipes and the fittings of the diesel delivery pipes to the injectors and the fittings of the diesel return pipe to the injection pump.
8. Fit the three retaining brackets, insert the pipes on the line that connect the injection pump to the injectors, tightening the retaining bolts.
9. Reconnect the four pipes connecting the injec-tion pump / injectors, tightening their fittings.

10. Reconnect the electrical connection for measuring the engine oil pressure.11. Install the fittings of the pipes connecting the injection pump-injectors, the pipe connected to the thermos tarter device and the electrical connection of the engine stop device.

12. Reconnect the pipe installed between the fuel filter and the fuel pump and reinsert the quick couplers.
13. Fit the pipe supplying the injection pump, connecting the quick couplers on the filter and on the injection pump.
14. Fit the pipe coming from the tank.
15. Reconnect the engine stop electromagnet cable.
16. Fit the throttle control lever and its retaining clip.
17. Install the hood.
18. Reconnect the battery negative cable and lower the hood.