John Deere 909J, 959J Tracked Feller Buncher Repair Manual (TM10272 and TM10271)

Table of Content
Repair Technical Manual – TM10273
Section 00—General Information
Group 0001—Safety Information
Group 0002—General Specifications
Group 0003—Torque Values
Group 0004—Fuels and Lubricants
Group 0005—Inspection and Procedures
Section 01—Track Drive
Group 0130—Remove and Install
Group 0131—Track Wear Specifications
Section 02—Leveling Frame
Group 0200—Remove and Install
Group 0260—Hydraulic System
Section 03—Axles and Suspension Systems
Group 0350—Axle Shaft, Bearings, and Reduction Gears
Group 0360—Hydraulic System
Section 04—Engine
Group 0400—Remove and Install
Group 0407—Oiling System
Group 0420—Fuel System
Group 0422—Starter Motor
Group 0423—Alternator
Section 05—Engine Auxiliary Systems
Group 0510—Cooling System
Group 0511—Radiator and Fan Shroud
Group 0520—Air Intake System
Group 0530—Exhaust System
Group 0540—Engine Mounts
Group 0564—Fuel Tank
Group 0574—Engine Wiring Harness
Section 17—Frames
Group 1740—Frame Installation
Group 1745—Leveler Frames
Group 1749—Chassis Weights
Section 18—Operator’s Station
Group 1810—Cab
Group 1830—Heating and Air Conditioning
Section 19—Sheet Metal and Styling
Group 1910—Engine Enclosure
Section 21—Main Hydraulic System
Group 2100—Remove and Install
Group 2160—Hydraulic System
Group 2162—Control Valves
Group 2164—Hydraulic Reservoir, Filters and Cooler
Group 2165—Cylinders
Section 31—Booms
Group 3100—Remove and Install
Group 3165—Hydraulic System
Section 43—Swing System
Group 4300—Remove and Install
Group 4350—Swing Gearbox
Group 4353—Swing Bearing
Group 4360—Hydraulic System
Section 99—Dealer Fabricated Tools
Group 9900—Dealer Fabricated Tools
Operation and Test Manual – TM10272
Section 9000—General Information
Group 01—Safety Information
Group 02—General Specifications
Group 03—Torque Values
Group 04—Fuels and Lubricants
Group 05—Inspection and Procedures
Section 9005—Operational Checkout Procedure
Group 10—Operational Checkout Procedure
Section 9010—Engine
Group 05—Theory of Operation
Group 15—Diagnostic Information
Section 9015—Electrical System
Group 05—System Information
Group 10—System Diagrams
Group 15—Sub-system Diagnostics
Group 20—References
Section 9020—Power Train
Group 05—Theory of Operation
Group 15—Diagnostic Information
Group 20—Adjustments
Group 25—Tests
Section 9025—Hydraulic System
Group 05—Theory of Operation
Group 15—Diagnostic Information
Group 20—Adjustments
Group 25—Test
Section 9031—Heating and Air Conditioning
Group 05—Theory of Operation
Group 15—Diagnostic Information
Essential tools required in performing certain service work are identified in this manual and are recommended for use.
Live with safety: Read the safety messages in the introduction of this manual and the cautions presented throughout the text of the manual.
This is the safety-alert symbol. When you see this symbol on the machine or in this manual, be alert to the potential for personal injury.
Technical manuals are divided in two parts: repair and operation and tests. Repair sections tell how to repair the components. Operation and tests sections help you identify the majority of routine failures quickly.
Information is organized in groups for the various components requiring service instruction. At the beginning of each group are summary listings of all applicable essential tools, service equipment and tools, other materials needed to do the job, service parts kits, specifications, wear tolerances, and torque values.
Technical Manuals are concise guides for specific machines. They are on-the-job guides containing only the vital information needed for diagnosis, analysis, testing, and repair.
Fundamental service information is available from other sources covering basic theory of operation, fundamentals of troubleshooting, general maintenance, and basic type of failures and their causes.