John Deere 710J Backhoe Loader Technical Manual (S.N 159770 – 161143 and after 172185 – )

Table of Contents
Repair Technical Manual – TM10875
Section 00—General Information
Group 0001—Safety Information
Group 0003—Torque Values
Section 01—Wheels
Group 0110—Powered or Non-Powered Wheels and Fastenings
Section 02—Axles and Suspension Systems
Group 0225—Input Drive Shafts and U-Joints
Group 0230—Non-Powered Wheel Axles
Group 0240—Powered Wheel Axle (MFWD)
Group 0250—Axle Shaft, Bearings, and Reduction Gears
Section 03—Transmission
Group 0300—Removal and Installation
Group 0315—Controls Linkage
Group 0325—Input Drive Shafts and U-Joint
Group 0350—Gears, Shafts, Bearings, and Power Shift Clutches
Group 0360—Hydraulic System
Section 04—Engine
Group 0400—Removal and Installation
Section 05—Engine Auxiliary Systems
Group 0505—Cold Weather Starting Aid
Group 0510—Cooling System
Group 0515—Speed Controls
Group 0520—Intake System
Group 0530—Exhaust System
Group 0560—External Fuel Supply System
Section 06—Torque Converter
Group 0651—Turbine, Gears and Shaft
Section 09—Steering System
Group 0960—Hydraulic System
Section 10—Service Brakes
Group 1011—Active Elements
Group 1060—Hydraulic System
Section 17—Frames, Chassis or Supporting Structure
Group 1749—Chassis Weights
Section 18—Operator’s Station
Group 1800—Removal and Installation
Group 1810—Operator Enclosure
Group 1821—Seat and Seat Belt
Group 1830—Heating and Air Conditioning
Section 19—Sheet Metal and Styling
Group 1910—Hood and Engine Enclosure
Group 1913—Miscellaneous Shields
Group 1921—Grille and Grille Housing
Group 1927—Fenders
Section 20—Safety, Convenience and Miscellaneous
Group 2001—Radio
Group 2004—Horn and Warning Devices
Section 21—Main Hydraulic System
Group 2160—Hydraulic System
Section 31—Loader
Group 3100—Loader
Group 3102—Bucket
Group 3104—Attachment Coupler
Group 3115—Control Linkages
Group 3160—Hydraulic System
Section 33—Backhoe
Group 3302—Bucket
Group 3315—Control Linkage
Group 3340—Frames
Group 3360—Hydraulic System
Section 99—Dealer Fabricated Tools
Group 9900—Dealer Fabricated Tools
Operation and Test Manual – TM10874
Section 9000—General Information
Group 01—Safety Information
Section 9001—Diagnostics
Group 10—Engine Control Unit (ECU)
Group 20—Flex Load Controller (FLC)
Group 30—Standard Display Monitor (SDM)
Section 9005—Operational Checkout Procedure
Group 10—Operational Checkout Procedure
Section 9010—Engine
Group 05—Theory of Operation
Group 15—Diagnostic Information
Group 20—Adjustments
Group 25—Tests
Section 9015—Electrical System
Group 05—System Information
Group 10—System Diagrams
Group 15—Sub-System Diagnostics
Group 16—Monitor Operation
Group 20—References
Section 9020—Power Train
Group 05—Theory of Operation
Group 15—Diagnostic Information
Group 20—Adjustments
Group 25—Tests
Section 9025—Hydraulic System
Group 05—Theory of Operation
Group 15—Diagnostic Information
Group 20—Adjustments
Group 25—Tests
Section 9031—Heating And Air Conditioning
Group 05—Theory Of Operation
Group 15—Diagnostic
Read the safety messages in the introduction of this manual and the cautions presented throughout the text of the manual.
Information is organized in groups for the various components requiring service instruction. At the beginning of each group are summary listings of all applicable essential tools, service equipment and tools, other materials needed to do the job, service parts kits, specifications, wear tolerances, and torque values.
John Deere recommends using only genuine John Deere replacement parts to ensure machine performance. Never substitute genuine John Deere parts with alternate parts not intended for the application as these can create hazardous situations or hazardous performance